Library

feed icon rss

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
Filter
  • 2000-2004
  • 1985-1989  (5)
  • 1905-1909
  • Chemical Engineering  (3)
  • 81.40E  (2)
  • 1
    Electronic Resource
    Electronic Resource
    Springer
    Applied physics 42 (1987), S. 227-232 
    ISSN: 1432-0630
    Keywords: 81.40E ; 61.80B ; 61.70T ; 71.55
    Source: Springer Online Journal Archives 1860-2000
    Topics: Mechanical Engineering, Materials Science, Production Engineering, Mining and Metallurgy, Traffic Engineering, Precision Mechanics , Physics
    Notes: Abstract We have investigated the annealing behaviour of electrically-active defects induced in virgin n-type and residual in As+ implanted p-type silicon after laser irradiation, using the rapid thermal annealing technique (RTA). Spectra from deep level transient spectroscopy (DLTS) show that three majority carrier traps at E (0.32 eV), E (0.45 eV) and E (0.53 eV) were induced in the n-type Si after Nd-Yag laser treatment at 1.6 J cm−2. Annealing in a rapid thermal furnace at 600 °C for times between 5 and 60 s resulted in a linear decrease of the concentration of these defects and for times ≧ 60 s, they are no longer detectable. A similar result was obtained in the case of the multiple energy As+ implanted samples in which two majority carrier traps at H (0.30 eV), H (0.58 eV) and a minority carrier trap E (0.53 eV) completely disappeared after annealing for 45 s at 600 °C, in spite of the very high concentration of the H (0.58 eV) defect (〉1015 cm−3 up to a depth of about 1.5 μm). A comparison of the annealing rates of the E (0.32 eV) trap using the RTA and the conventional thermal annealing (CTA) techniques at 600 °C showed that the former is at least 30 times faster than the latter. Sheet resistance measurements show that the level of dopant deactivation, due to post-laser thermal treatment at 500 °C (in order to obtain the same reduction in residual defect concentration), is less in the RTA processed samples than in those annealed using conventional methods. These results lend strong support to the hypothesis of ionization-induced enhancement of defect annealing, and to our knowledge, represent the first report of the observation of the phenomenon using the RTA technique.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 2
    Electronic Resource
    Electronic Resource
    Springer
    Applied physics 49 (1989), S. 233-237 
    ISSN: 1432-0630
    Keywords: 61.16D ; 61.70N ; 81.40E ; 61.50
    Source: Springer Online Journal Archives 1860-2000
    Topics: Mechanical Engineering, Materials Science, Production Engineering, Mining and Metallurgy, Traffic Engineering, Precision Mechanics , Physics
    Notes: Abstract We have studied the influence of conventional and rapid thermal treatments at 850°C for 30 min and 10 s, respectively, on the recombination activity of theε9,ε13 (P-type) andε25 (N-type) grain boundaries in silicon. The analyses were made by scanning electron microscopy (SEM) working in the electron beam induced current mode (EBIC) and completed by minority carrier diffusion length measurements. The main result obtained from this study shows the importance of the rapid thermal process as a suitable thermal treatment for polycrystalline materials.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 3
    Electronic Resource
    Electronic Resource
    Hoboken, NJ : Wiley-Blackwell
    AIChE Journal 34 (1988), S. 519-523 
    ISSN: 0001-1541
    Keywords: Chemistry ; Chemical Engineering
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Process Engineering, Biotechnology, Nutrition Technology
    Additional Material: 8 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 4
    Electronic Resource
    Electronic Resource
    Hoboken, NJ : Wiley-Blackwell
    AIChE Journal 31 (1985), S. 473-482 
    ISSN: 0001-1541
    Keywords: Chemistry ; Chemical Engineering
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Process Engineering, Biotechnology, Nutrition Technology
    Notes: Rates of mass and momentum transport in narrow flow channels (gaps 0.2-0.5 mm) have been determined over a wide range of flow velocities, 220-7,700 cm/sec (Re 1,300 to 22,000). Existing correlations that apply to smooth channels of much larger hydraulic diameter were found to be valid for the narrow channels as well. However, in the turbulent regime the condition of hydraulic smoothness could be satisfied only when the walls were optically smooth. Transport rates to rough walls were also measured. The ratio of the mass transport to the momentum transport in the form of jD/(f/2) - a measure of the improved mass transfer compared to the increased pressure drop - is given for the smooth and rough-wall cells over the Re range studied.
    Additional Material: 12 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 5
    Electronic Resource
    Electronic Resource
    Stamford, Conn. [u.a.] : Wiley-Blackwell
    Polymer Engineering and Science 29 (1989), S. 1165-1168 
    ISSN: 0032-3888
    Keywords: Chemistry ; Chemical Engineering
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Mechanical Engineering, Materials Science, Production Engineering, Mining and Metallurgy, Traffic Engineering, Precision Mechanics , Physics
    Notes: A method is presented to study the mechanical behavior of soft, UV curable coating material as a function of temperature of the prepolymer at cure. For such materials, the crosslink density (hence, equilibrium modulus) is found to decrease with increasing cure temperature. The three primary coatings are: a polyurethane acrylate with a nominal equilibrium tensile modulus of 200 psi, a polyurethane acrylate with a nominal equilibrium modulus of 1200 psi, and a non-urethane acrylate with a nominal equilibrium tensile modulus of 60 psi.
    Additional Material: 9 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...