Library

feed icon rss

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
  • 11
    Electronic Resource
    Electronic Resource
    Springer
    Journal of materials science 6 (1995), S. 390-395 
    ISSN: 1573-4838
    Source: Springer Online Journal Archives 1860-2000
    Topics: Medicine , Technology
    Notes: Stimulated whole saliva samples were collected from 30 healthy individuals and analysed with a cone and plate viscometer. On the basis of these dynamic viscosity measurements saliva from patients, who represented the mean value and two standard deviations above and below the mean value, were selected for frictional force testing. Four archwire/bracket couples (SS/SS, SS/PCA, β-Ti/SS, and β-Ti/PCA) were each tested in these three salivas as well as in the dry state a total of five times, each at five different normal loads. With two exceptions no significant differences were found between any of the three wet states for any couple studied. When the dry state was compared to any of the wet states, the SS archwire couples showed a singificant increase in frictional forces, while the β-Ti archwire couples showed a slight decrease in frictional forces, which was not statistically significant.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 12
    Electronic Resource
    Electronic Resource
    Springer
    Journal of materials science 6 (1995), S. 385-389 
    ISSN: 1573-4838
    Source: Springer Online Journal Archives 1860-2000
    Topics: Medicine , Technology
    Notes: The dynamic viscosity (μ) of stimulated whole saliva in a typical pre-orthodontic sample population was characterized as a function of temperature (T). Samples were collected from 30 adolescents or young adults, after screening for factors that are known to have an effect on salivary viscosity. Using a cone and plate viscometer, 1.5 ml of stimulated whole saliva was evaluated at a constant shear rate of 450 s-1 from T=20°C to T=40°C. Data from the μ-T plots showed a negative dependence of the form, μ=a−bT, over a range of μ from 1.08 to 2.45 centipoise (cps) at 34°C. Most of the samples fell into a narrow envelope, where the mean μ of the saliva samples ranged from 2.42±0.61 cps at 20°C to 1.57±0.32 cps at 37°C. With regard to sample stability, viscosity-time plots indicated that a small but predictable decrease in μ occurred during the 3 h period. The μ-T plots generated from fresh and frozen saliva samples demonstrated an appreciable change in μ as a result of refrigeration. With regard to sample reproducibility, viscometric data obtained from a typical pre-orthodontic patient over a 1-week period fluctuated within a fairly broad envelope of values.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 13
    Electronic Resource
    Electronic Resource
    Springer
    Journal of materials science 11 (2000), S. 683-693 
    ISSN: 1573-4838
    Source: Springer Online Journal Archives 1860-2000
    Topics: Medicine , Technology
    Notes: Abstract Prototype continuous, unidirectional, fiber-reinforced composite archwires were manufactured into round and rectangular profiles utilizing a photo-pultrusion process. Both 0.022 inch (0.56 mm) diameter and 0.021 × 0.028 inch (0.53 × 0.71 mm) rectangular composites were formed utilizing commercially available S2-glass® reinforcement within a polymeric matrix. Reinforcement was varied according to the number, denier and twists per inch (TPI) of four S2-glass® yarns to volume levels of 32–74% for round and 41–61% for rectangular profiles. Cross-sectional geometry was evaluated via light microscopy to determine loading characteristics; whereas two flexural properties (the elastic moduli and flexural strengths) were determined by 3-point bending tests. Morphological evaluation of samples revealed that as the TPI increased from 1 to 8, the yarns were more separated from one another and distributed more peripherally within a profile. For round and rectangular profiles utilizing 1 TPI fibers, moduli increased with fiber content approaching theoretical values. For round profiles utilizing 1 TPI and 4 TPI fibers, flexural strengths increased until the loading geometry was optimized. In contrast, the flexural strengths of composites that were pultruded with 8 TPI fibers were not improved at any loading level. Doubling the denier of the yarn, without altering the loading, increased both the moduli and flexural strengths in rectangular samples; whereas, the increases observed in round samples were not statistically significant. At optimal loading the maximum mean moduli and strengths equaled 53.6 ± 2.0 and 1.36 ± 0.17 (GPa) for round wire and equaled 45.7 ± 0.8 and 1.40 ± 0.05 (GPa) for rectangular wires, respectively. These moduli were midway between that of martensitic NiTi (33.4 GPa) and beta-titanium (72.4 GPa), and produced about one-quarter the force of a stainless steel wire per unit of activation. Values of strengths placed this composite material in the range of published values for beta-titanium wires (1.3–1.5 GPa). © 2000 Kluwer Academic Publishers
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 14
    ISSN: 1573-4838
    Source: Springer Online Journal Archives 1860-2000
    Topics: Medicine , Technology
    Notes: Methyl methacrylate and six solutions of methyl methacrylate/dibutyl phthalate (nominally 5 to 30% v/v) were polymerized into thin sheets using gamma radiation. Dynamic mechanical spectra of the storage modulus, loss modulus and loss tangent, as well as changes in length, were investigated as a function of temperature. From these measurements, the depression of the storage modulus and glass-transition temperature were obtained. Subsequently, differential scanning calorimetry (DSC) and cross-polarization-magic-angle-spinning NMR were used to obtain additional glass-transition and relaxation-time measurements. Based upon these experiments, a specific form of the rule of mixtures described the depression of the glass-transition temperature. From storage-modulus measurements, antiplasticization was evidenced at very low temperatures and at compositions greater than 25% v/v. Solid-state NMR confirmed that plasticization causes an increase in polymer main-chain motion via the physical loosening of secondary bonds between polymer chains.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 15
    Electronic Resource
    Electronic Resource
    Springer
    Journal of materials science 6 (1995), S. 569-576 
    ISSN: 1573-4838
    Source: Springer Online Journal Archives 1860-2000
    Topics: Medicine , Technology
    Notes: Preterm premature rupture of the chorioamniotic membrane frequently leads to preterm birth and perinatal mortality. To ascertain whether the rupture of these membranes is influenced by variations in environmental pH and sodium concentration, we punctured 180 specimens from 9 membranes that were equilibrated in solutions of different pH, and 196 specimens from 10 membranes that were equilibrated in solutions with different sodium concentrations. Whole-membrane mechanical characteristics—strength, stiffness, toughness and ductility—were measured. These characteristics were defined based on a variant of the weakest-link theory: from a pool of three to five specimens, the specimen that had the lowest values of strength and concomitant values of stiffness, toughness, and ductility represents the mechanical characteristics of the entire membrane section. Strength-related mechanical characteristics—strength, stiffness and toughness—correlated negatively with pH (p〈0.001, p〈0.001, and p〈0.02, respectively), while ductility did not correlate significantly with pH. Membrane hydration and thickness correlated positively with pH (p〈0.001). The greatest increase in hydration accompanied by the greatest drop in strength, stiffness and toughness was observed between pH values of 3.68 and 5.58, suggesting that insufficient quantities of vaginal H+ could cause—as well as mark—premature rupture of the chorioamniotic membrane. No whole—membrane mechanical characteristics correlated significantly with changes in sodium concentration. Membrane hydration and thickness had slight positive correlations with sodium concentration (p〈0.05). Changes solely in the sodium concentration of the amniotic fluid during normal pregnancy are not sufficient to facilitate rupture at term.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 16
    Electronic Resource
    Electronic Resource
    Springer
    Journal of materials science 5 (1994), S. 130-137 
    ISSN: 1573-4838
    Source: Springer Online Journal Archives 1860-2000
    Topics: Medicine , Technology
    Notes: The mechanical characteristics of the chorioamniotic membrane were evaluated with a new burst test apparatus by rupturing 35 specimens that were taken from a sample of seven afterbirths. ‘Strength’, ‘stiffness’, ‘toughness’, and ‘ductility’ were measured. Mechanical characteristics did not change significantly with variation in thickness. While ductility should not correlate with thickness, the lack of a significant increase in strength, stiffness and toughness with an increase in thickness is most unusual and requires an explanation. Subsequently, an additional experiment, which was designed to ascertain the mechanical stability of membrane specimens with prolonged exposure to air, showed a dramatic increase in stiffness as membranes were allowed to dry. The increase in stiffness indicates that strength and toughness also increase with drying, provided that ductility remains constant. Thus, the degree of hydration of the membrane, which is reflected in thickness, regulates mechanical characteristics. The increase in the water content of certain amniotic layers has a lubricating effect on the amnion-chorion interface. This lubrication increases as term approaches. Thus, hydration must increase as gestation progresses, and strength, stiffness, and toughness must decrease until the membrane is weak enough to rupture at the end of gestation. Thus, hydration must increase as gestation progresses, and strength, stiffness, and toughness must decrease until the membrane is weak enough to rupture at the end of gestation.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 17
    Electronic Resource
    Electronic Resource
    Springer
    Journal of materials science 6 (1995), S. 377-384 
    ISSN: 1573-4838
    Source: Springer Online Journal Archives 1860-2000
    Topics: Medicine , Technology
    Notes: Degradative characteristics were studied using specimens of three polyurethane-based elastomeric modules that were treated in solutions of varying acidity, oxygen content and temperature. After periods of 10 and 100 days, molecular weight distribution changes, mechanical property changes and elemental chemistry changes were studied using gel permeation chromatography (GPC), stress-relaxation testing and X-ray photoelectron spectroscopy (XPS), respectively. As determined through analyses of the molecular, mechanical, and elemental changes after treatment, the degradative mechanism was influenced by whether the polyurethane was polyester-based or polyether-based, and the degree of structural degradation was influenced by the type and duration of conditioning treatment. Degradation of the polyester-based materials after treatment was dominated by a chain scission mechanism; conversely, the degradation of the polyether-based material was dominated by a crosslinking mechanism. Among the conditioning treatments, the combined effects of an increase in acidity, oxygen content and temperature most influenced the degree of degradation with time, with the increase in temperature having the greatest effect of any of the single variables investigated.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 18
    ISSN: 1573-4838
    Source: Springer Online Journal Archives 1860-2000
    Topics: Medicine , Technology
    Notes: Abstract The frictional characteristics of prototype composite archwires were investigated. The resistance to sliding was measured in the dry state for wires with three different volume fractions of fiber reinforcement against stainless steel, polycrystalline alumina, and single crystal alumina orthodontic brackets. Each archwire and bracket combination was tested at 34 °C with twelve different normal forces (from 0–400 g) and six different angulations (from 0°–12.5°). The kinetic coefficients of friction were determined from the slopes of linear regressions through plots of the resistance to sliding versus normal force data. The y-intercepts of these regressions were also evaluated as indicators of the binding magnitude. The tested archwire samples were examined for wear using a scanning electron microscope. A fully factorial model analysis-of-variance showed no significant differences in the frictional coefficients for changes in bracket material, reinforcement level, or angulation. Highly significant differences were observed in the y-intercepts for changes in the reinforcement level and angulation. Highly significant, positive, and linear correlations between the y-intercepts and angulations were also established. Abrasive wear of the composite surface was observed at the archwire–bracket interface, particularly at higher normal forces and angulations. Relative to other frictional studies of metallic archwire materials, the composite archwires had higher kinetic coefficients of friction than stainless steel but lower coefficients than either nickel titanium or beta-titanium archwires against all bracket materials tested. © 1998 Kluwer Academic Publishers
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 19
    ISSN: 1573-4838
    Source: Springer Online Journal Archives 1860-2000
    Topics: Medicine , Technology
    Notes: Abstract The flexural properties and failure morphologies of dimethacrylate-copolymer composites reinforced with either S2-glass® or quartz fibres (≈33–66 vol%) were examined after hydrothermal ageing (0–3 mon at 37 °C). Initially the S2-glass® composites were generally stiffer and stronger than comparably reinforced quartz composites, but within 1 wk the properties of S2-glass® composites decreased by 12%–26%. The properties ofquartz composites were relatively stable, except for those of composites with the least reinforcement (35 vol%), which decreased by roughly 15%. Scanning electron microscopy revealed that in all composites buckling had occurred at the site of load application. Evidence of good fibre–matrix adhesion was observed for both types of composites under all conditions. Modelling of degradation between 1 wk and 3 mon revealed that: (1) the only temporal change was a slight increase in the stiffness of S2-glass® composites; and (2) higher reinforcement levels reduced the retention of strength in S2-glass® composites but had the opposite effect (on both properties) for quartz composites (p〈0.05). For the most highly reinforced S2-glass® composites, susceptibility to degradation was offset by high initial properties; and after ageing (elastic modulus ≈50 GPa, strength ≈1.2 GPa), these composites were still, on average, approximately 25% stiffer and 50% stronger than the more hydrostable quartz counterparts. © 1998 Kluwer Academic Publishers
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 20
    Electronic Resource
    Electronic Resource
    Springer
    Journal of materials science 13 (1994), S. 849-851 
    ISSN: 1573-4811
    Source: Springer Online Journal Archives 1860-2000
    Topics: Mechanical Engineering, Materials Science, Production Engineering, Mining and Metallurgy, Traffic Engineering, Precision Mechanics
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...