Library

feed icon rss

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
Filter
  • Engineering General  (2)
  • Key words: Apoptosis — 4-Aminopyridine — High K+ concentration — Gene expression — Membrane potential  (1)
  • 1
    Electronic Resource
    Electronic Resource
    Springer
    The journal of membrane biology 172 (1999), S. 113-120 
    ISSN: 1432-1424
    Keywords: Key words: Apoptosis — 4-Aminopyridine — High K+ concentration — Gene expression — Membrane potential
    Source: Springer Online Journal Archives 1860-2000
    Topics: Biology , Chemistry and Pharmacology
    Notes: Abstract. Mcl-1, a member of the Bcl-2 family, has been identified as an inhibitor of apoptosis induced by anticancer agents and radiation in myeloblastic leukemia cells. The molecular mechanism underlying this phenomenon, however, is not yet understood. In the present study, we report that hyperpolarization of the membrane potential is required for prevention of mcl-1 mediated cell death in murine myeloblastic FDC-P1 cells. In cells transfected with mcl-1, the membrane potential, measured by the whole-cell patch clamp, was hyperpolarized more than −30 mV compared with control cells. The membrane potential was repolarized by increased extracellular K+ concentration (56 mV per 10-fold change in K+ concentration). Using the cell-attached patch-clamp technique, K+ channel activity was 1.7 times higher in mcl-1 transfected cells (NP o = 22.7 ± 3.3%) than control cells (NP o = 13.2 ± 1.9%). Viabilities of control and mcl-1 transfected cells after treatment with the cytotoxin etoposide (20 μg/ml), were 37.9 ± 3.9% and 78.2 ± 2.0%, respectively. Suppression of K+ channel activity by 4-aminopyridine (4-AP) before etoposide treatment significantly reduced the viability of mcl-1 transfected cells to 49.0 ± 4.6%. These results indicate that as part of the prevention of cell death, mcl-1 causes a hyperpolarization of membrane potential through activation of K+ channel activity.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 2
    Electronic Resource
    Electronic Resource
    Chichester [u.a.] : Wiley-Blackwell
    International Journal for Numerical Methods in Engineering 36 (1993), S. 3097-3130 
    ISSN: 0029-5981
    Keywords: Engineering ; Engineering General
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Mathematics , Technology
    Notes: This work presents a specialization of the integral identities used in the boundary element method. This modification is especially tailored to deal with three-dimensional elastostatic problems involving geometries which contain two parallel planar surfaces (e.g. three-dimensional plate problems). The formulation makes use of the three-dimensional fundamental solution for a point load acting in the interior of an infinite layer of uniform thickness (obtained by Benitez and Rosakis8,9).It is shown that this procedure is especially suited for the analysis of three-dimensional problems involving cavities in plate structures. In such problems it is demonstrated that, in addition to the cavity surfaces, only the lateral surfaces of the structure need to be discretized, with no discretization required on the traction-free parallel surfaces.
    Additional Material: 6 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 3
    Electronic Resource
    Electronic Resource
    Chichester [u.a.] : Wiley-Blackwell
    International Journal for Numerical Methods in Engineering 36 (1993), S. 3131-3159 
    ISSN: 0029-5981
    Keywords: Engineering ; Engineering General
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Mathematics , Technology
    Notes: This work applies the specialization of the integral identities used in the boundary element method to the numerical solution of three-dimensional elasticity problems involving geometries containing two parallel planar surfaces (see Part I this issue). Two three-dimensional problems are numerically analysed by using the above procedure. These are the problems of pressurized circular and elliptical holes in infinite plates of uniform thickness. For the circular hole problem, the accuracy of our scheme is established by direct comparison of our results with the available analytical solution. For the ellipse problem, with an aspect ratio of 4:1, the boundary element results are compared with those of a finite element calculation.
    Additional Material: 38 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...