Library

feed icon rss

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
  • 1
    Electronic Resource
    Electronic Resource
    Weinheim : Wiley-Blackwell
    Angewandte Makromolekulare Chemie 150 (1987), S. 137-150 
    ISSN: 0003-3146
    Keywords: Chemistry ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Description / Table of Contents: Es wurde der relative Wirkungsgrad von fünf handelsüblichen Stabilisatoren bei Photooxidation und thermischer Alterung von Polypropylen (PP) anhand der Änderungen der mechanischen Eigenschaften untersucht. Es wurden Polypropylenproben mit unterschiedlichem Anteil an Cyasorb UV-531 hergestellt (bezeichnet als PC0.5-31, PC1-31, PC1.5-31 und PC2-31). Der Einfluß der Photooxidation auf das thermische Verhalten ist mit Hilfe der Differentialscanningkalorimetrie und durch thermogravimetrische Analysen untersucht worden. 2-Hydroxy-4-n-octyloxybenzophenon (2 Gew.-%) war am wirksamsten, Polypropylen, gegen Verfärbung und Brüchigkeit zu stabilisieren. Bei einer Probe mit 1% Stabilisatorzusatz fanden sich nach 32 h Bestrahlung noch 81% des ursprünglichen Wertes der Streckgrenze gegenüber 18% bei unstabilisiertem PP.
    Notes: The relative effectiveness of five commercially available stabilizers on the photooxidation and thermal ageing of polypropylene (PP) was investigated by following changes in mechanical properties. Samples of PP containing different percentages of Cyasorb UV-531 were prepared (designated as PC0.5-31, PC1-31, PC1.5-31, and PC2-31, respectively). The effect of photooxidation on thermal behaviour was investigated by differential scanning calorimetry and thermogravimetric analysis. 2-Hydroxy-4-n-octyloxy benzophenone (2% w/w) was most effective in stabilizing PP towards discolouration and brittleness. After 32 h irradiation, 81% retention in yield strength was observed in case of PC1-31 against 18% in case of PP.
    Additional Material: 8 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 2
    Electronic Resource
    Electronic Resource
    Weinheim : Wiley-Blackwell
    Angewandte Makromolekulare Chemie 168 (1989), S. 217-223 
    ISSN: 0003-3146
    Keywords: Chemistry ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: The paper describes the successful synthesis of silicon containing bismaleimide resin 4,4′-carbo(4,4′-bismaleimido phenoxy)diphenyl silane. The char yield of the bismaleimide resin in N2 atmosphere was found to be 55% at 800°C. Chain extension of bismaleimide with 4,4′-diamino diphenyl sulfone reduced the char yield and thermal stability.
    Additional Material: 3 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 3
    Electronic Resource
    Electronic Resource
    Weinheim : Wiley-Blackwell
    Angewandte Makromolekulare Chemie 205 (1993), S. 47-58 
    ISSN: 0003-3146
    Keywords: Chemistry ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Description / Table of Contents: Methylmethacrylat (MMA) mit einem Prepolymergehalt von 6-8% wurde mit unterschiedlichen Anteilen (1-20%) 2-Ethylhexylmethacrylat (EMMA), n-Hexylmethacrylat (HMA), 2-Ethylhexylacrylat (EHA) oder n-Hexylacrylat (HA) copolymerisiert. Aus den erhaltenen Copolymeren wurden Folien hergestellt, an denen der Einfluß der Copolymerstruktur auf Lichtdurchlässigkeit, Dichte und mechanische Eigenschaften ermittelt wurde. zugsfestigkeit and Speichermodul nahmen mit zunehmendem Comonomergehalt ab. Die Dehnung stieg im Fall von MMA/EHA- und MMA/HA-Copolymerfolien mit 15 und 20 Gew.-% Comonomeranteil merklich an. Mittels DMTA wurde die Erweichungstemperatur der Copolymeren bestimmt. Die HDT und die Erweichungstemperatur nahmen unter Biegebelastung mit steigendem Comonomergehalt de Copolymeren ab.
    Notes: The paper describes the fabrication of cast acrylic sheets by copolymerizing a prepolymer syrup of methyl methacrylate (MMA) with varying amounts (1-20 wt.-%) of 2-ethylhexyl methacrylate (EHMA), n-hexyl methacrylate (HMA), 2-ethylhexyl acrylate (EHA) and n-hexyl acrylate (HA). The effect of structure of copolymer on light transmittance, density and mechanical properties was evaluated. Tensile strength and storage modulus decreased with increasing comonomer content. Strain increased significantly in the case of MMA/EHA and MMA/HA copolymer sheets having 15 and 20 wt.-% of comonomer. Softening temperature of copolymer samples was determined using dynamic mechanical thermal analysis. Heat deflection temperature under flexural load and softening temperature decreased with increasing comonomer content in copolymer.
    Additional Material: 3 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 4
    ISSN: 0003-3146
    Keywords: Chemistry ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Description / Table of Contents: Der Einfluß von Zusammensetzung und chemischer Struktur auf die thermischen Eigenschaften von Polyimiden aus handelsüblichen Allyl-„Nadimid“-Harzen und Phosphor enthaltenden “Nadimid”-Harzen wurde untersucht. Thermogravimetrische Messungen unter Stickstoff an Harzen, die 1 h bei 300 gehärtet wurden, ergaben eine Erhöhung der thermischen Stabilität.
    Notes: The effect of composition and chemical structure of addition polyimides on thermal characteristics was investigated using commercially available allyl nadic-imide resins and phosphorus-containing nadimide resins. Thermogravimetric analysis, in N2 atmosphere, of resins cured at 300°C for 1 h revealed improvement of thermal stability.
    Additional Material: 4 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 5
    ISSN: 0003-3146
    Keywords: Chemistry ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Description / Table of Contents: 2,4-Toluylendiisocyanat, 2-Hydroxyethylmethacrylat und Ethandiol wurden in einer zweistufigen Reaktion zu einem Urethan-Methacrylat umgesetzt, welches unter Verwendung von Dibenzoylperoxid/N,N′-Dimethylanilin in Gegenwart verschiedener Konzentrationen von Methylmethacrylat oder Styrol ausgehärtet wurde. Dabei wurde ein Anstieg der Gelierungszeit mit zunehmender Comonomerkonzentration und abnehmender Initiatorkonzentration beobachtet. Die thermogravimetrische Analyse zeigt im Temperaturbereich 230-500°C unter Stickstoff einen zweistufigen Abbau der gehärteten Harze. Ihre thermische Stabilität hängt von der Art und Konzentration des Comonomeren ab.
    Notes: Urethane methacrylate monomer (UMA) containing methacryloyl group was prepared from toluylene diisocyanate (TDI), 2-hydroxyethyl methacrylate (HEMA), and ethylene glycol by a two step reaction. Curing was investigated using benzoyl peroxide and N,N-dimethylaniline as initiator system. The effect of concentration of initiator and reactive diluents, i.e., methyl methacrylate and styrene, on gel point was determined. An increase in gel time was observed by increasing the concentration of reactive diluent or decreasing the concentration of initiator. In TG traces (recorded in nitrogen atmosphere) of cured resins two step decomposition was observed in the temperature range of 230 to 500°C. The thermal stability of copolymers was influenced by the nature and content of reactive diluent.
    Additional Material: 3 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 6
    Electronic Resource
    Electronic Resource
    Weinheim : Wiley-Blackwell
    Angewandte Makromolekulare Chemie 212 (1993), S. 67-75 
    ISSN: 0003-3146
    Keywords: Chemistry ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Description / Table of Contents: Die Härtungseigenschaften des Bismethacrylat-Derivates von Bisphenol-A-diglycidylether (VE-Harz) mit Styrol und α-Methylstyrol (MS) als Reaktivverdünner wurden untersucht. Ein zunehmender Gehalt an MS verzögerte die Härtung. Mit Glasfasermatten, die teilweise mit γ-Methacryloyloxyropyl-trimethoxysilan (MTS) behandelt waren, wurden Composites hergestellt, deren Grenzflächen-Scherspannung mit der Ein-Faser-Methode gemessen wurde. Die Beschichtung mit MTS verbesserte die Grenzflächen-Scherspannung der Composites um ca. 30-50%. Ein MS-Gehalt von bis zu 5 Gew.-% MS hatte keinen Einfluß auf die interlaminare Scherfestigkeit (ILSS), weder bei den glasfaserverstärkten Composites noch bei den Ein-Faser-Proben. Eine Erhöhung des MS-Anteils auf 15 Gew.-% verbesserte sowohl die ILSS als auch die Biegesteifigkeit und die Biegefestigkeit.
    Notes: The curing behaviour of bismethacryloyl derivative of diglycidyl ether of bisphenol A (vinyl ester VE resin) containing styrene and α-methyl styrene (MS) as reactive diluents was studied. Delayed curing was observed in samples containing increasing proportions of MS. Interfacial shear stress of untreated as well as γ-methacryloyloxy-propyl trimethoxy silane (MTS) treated, glass fibre-reinforced VE resin composites were measured by single fibre technique. In comparison to untreated glass fibres, a 30 - 50% increase in interfacial shear stress was observed in composites based on MTS treated glass fibres. Addition of up to 5 wt.-% MS to VE resin did not affect the interfacial shear strength (ILSS). This behaviour was observed by using ILSS measurement of both glass fabric-reinforced composites as well as single fibre specimens. Further increase in MS to 15 wt.-% resulted in an increase in ILSS and bending stiffness as well as flexural strength.
    Additional Material: 3 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 7
    Electronic Resource
    Electronic Resource
    Weinheim : Wiley-Blackwell
    Angewandte Makromolekulare Chemie 248 (1997), S. 95-104 
    ISSN: 0003-3146
    Keywords: Chemistry ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Description / Table of Contents: Copolymere aus Methylmethacrylat (MMA) und Cardanylmethacrylat (CMA) wurden synthetisiert, charakterisiert und hinsichtlich ihre physikomechanischen Eigenschaften untersucht. Die mit Benzoylperoxid initiierte Copolymerisation wurde mit unterschiedlichen Anteilen von CMA(0,02-0,01 mol/mol) im Reaktionsansatz bei 80°C durchgeführt. Die Strukturen der Copolymeren wurden mit FTIR- und 1H-NMR-Spektroskopie charakterisiert. Die thermische Stabilität der Copolymeren wurde mit dynamischer Thermogravimetrie bestimmt. Es zeigte sich, daß die thermische Stabilität der Polymeren durch den Einbau von CMA in die MMA-Hauptketten verbessert wird.
    Notes: Copolymers of methyl methacrylate (MMA) and cardanyl methacrylate (CMA) were synthesized, characterized and their physico-mechanical properties were investigated. The benzoyl peroxide-initiated copolymerization was carried out by using different mole fractions of CMA (0.02-0.10) in the initial feed at 80°C. Structural characterization of copolymers was done using FTIR and 1H NMR spectroscopic techniques. The thermal stability of the copolymers was evaluated using dynamic thermogravimetry. Incorporation of CMA in the MMA backbone leads to an improvement in thermal stability.
    Additional Material: 4 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 8
    Electronic Resource
    Electronic Resource
    New York : Wiley-Blackwell
    Die Makromolekulare Chemie 170 (1973), S. 117-130 
    ISSN: 0025-116X
    Keywords: Chemistry ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Description / Table of Contents: Durch Polykondensation von Terephthalsäure (TA), Isophthalsäure (IA) und Nitrophthalsäure (NA) mit Hydrazinsulfat (HS) in Gegenwart von rauchender Schwefelsäure, wurden Poly(1,3,4-oxadiazol-2,5-diyl-1,4-phenylen) (I) und Poly(1,3-phenylen-1,3,4-oxadiazol-2,5-diyl-1,4-phenylen) (II) und dessen Nitroderivat erhalten. Homopolymere von TA und HS, sowie Copolymere vom Typ TA/IA-HS und TA/NA-HS mit verschiedenen STAUDINGER Indices wurden unter verschiedenen Reaktionsbedingungen erhalten. Die Produkte wurden spektroskopisch (sichtbares Licht, UV, IR) und durch Elementaranalyse untersucht, wobei Poly(oxadiazoldiylphenylen)- und Poly(hydrazoterephthaloyl)-Strukturen nachgewiesen werden konnten. Die Polymeren waren thermisch stabil. Die meisten zeigten unterhalb von 360°C keine Gewichtsabnahme. Erst bei 460-480°C wiesen die Thermogramme Maxima des Gewichtsverlustes auf. Aus solchen Messungen wurden die Aktivierungsenergien E und die Frequenzfaktoren A der thermischen Zersetzung ermittelt. Zwischen dem STAUDINGER Index einerseits und E oder auch der “integral procedural decomposition temperature” andererseits, wurden lineare Abhängigkeiten festgestellt. Es zeigte sich, daß die Polymeren vom Typ I stabiler waren, als die Copolymeren vom Typ II von ähnlichem Molekulargewicht.
    Notes: Poly(1,3,4-oxadiazole-2,5-diyl-1,4-phenylene) (I) and poly(1,3-phenylene-1,3,4-oxadiazole-2,5-diyl-1,4-phenylene) (II) and its nitroderivative have been prepared by condensation polymerization using fuming H2SO4 and different quantities of terephthalic acid (TA), isophthalic acid (IA), nitrophthalic acid (NA), and hydrazine sulphate (HS) respectively. Homopolymers of TA and HS, and copolymers of TA, IA, HS and TA, NA, and HS of different intrinsic viscosities were prepared by varying the reaction conditions. The polymer structures were investigated by visible range spectra, UV spectra, IR spectra and elemental analysis. The existence of poly(1,3,4-oxadiazolediyl-phenylene)- and poly(hydrazoterephthaloyl)-structures was revealed by these studies. These polymers were thermally stable and most of them did not show any loss in weight below 360°C. The maximum weight loss was in the temperature range of 460-480°C. The activation energy E and the frequency factor A for the thermal degradation were evaluated. Linear relationships between E and the intrinsic viscosity and between the “integral procedural decomposition temperature” and the intrinsic viscosity were observed. The polymers I showed a higher stability than the copolymers II of similar molecular weights.
    Additional Material: 9 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 9
    Electronic Resource
    Electronic Resource
    New York : Wiley-Blackwell
    Die Makromolekulare Chemie 175 (1974), S. 2515-2524 
    ISSN: 0025-116X
    Keywords: Chemistry ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Description / Table of Contents: Die Chlorwasserstoffabspaltung aus 1-Chlordodekan (1-DDCl), 2-Chlordodekan (2-DDCl), 1,1,3-Trichlornonan (TCN) und Dichlornonen (DCN) in Stickstoffatmosphäre wurde in flüssiger Phase im Temperaturbereich von 202 - 262°C untersucht. Basierend auf der Geschwindigkeitskonstante der Zersetzungsreaktion und der Aktivierungsenergie ergibt sich als Stabilitätsskala für die Chlorwasserstoffabspaltung in flüssiger Phase: 1-DDCl〉2-DDCl〉TCN〉DCN. Die Lösungsmittel Methylsalicylat und Eugenol beeinflussen die Chlorwasserstoffabspaltung aus Polyvinylchlorid. Aus diesem Grund dürfte der molekulare Mechanismus, der bei der Zersetzung dieser Chlorverbindungen wirksam ist, für den Abbau des Polyvinylchlorids nicht zutreffend sein.
    Notes: The liquid phase dehydrochlorination of 1-chlorododecane (1-DDCl), 2-chlorododecane (2-DDCl), 1,1,3-trichlorononane (TCN), and dichlorononene (DCN) was investigated in the temperature range of 202 - 262°C in a nitrogen atmosphere. On the basis of the decomposition rate constant and activation energy the stability order for the dehydrochlorination in liquid phase was found to be 1-DDCl〉2-DDCl〉TCN〉DCN. The influence of the solvents methyl salicylate and eugenol on the dehydrochlorination of these chloro compounds was different from their influence on the dehydrochlorination of PVC. Therefore, a molecular mechanism for dehydrochlorination believed to be operating in these chloro compounds may not be operating in PVC degradation.
    Additional Material: 7 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 10
    Electronic Resource
    Electronic Resource
    New York, NY [u.a.] : Wiley-Blackwell
    Journal of Applied Polymer Science 17 (1973), S. 2097-2108 
    ISSN: 0021-8995
    Keywords: Chemistry ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Mechanical Engineering, Materials Science, Production Engineering, Mining and Metallurgy, Traffic Engineering, Precision Mechanics , Physics
    Notes: The reaction of nylon 6 with dimethyldichlorosilane and vinylmethyldichlorosilane was investigated. Bright, 20-denier monofilament, nylon 6 yarns with 12.83% nitrogen, 61.16% carbon, and 10.16% hydrogen content were taken. Benzene or toluene was used as solvent for the reagents. The extent of reaction was estimated from the increase in weight of the parent yarn. Reaction was carried in the presence of nitrogen or in atmospheric oxygen (air). The per cent weight gain increased with increase in concentration of reagents, time, and temperature of the reaction. Viscosity and dyeability of the modified samples were measured, and in some samples the percentage of carbon, hydrogen, and nitrogen was also determined.
    Additional Material: 4 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...