Materials analysis of the TITAN-I reversed-field-pinch fusion power core

https://doi.org/10.1016/0920-3796(93)90126-3Get rights and content

Abstract

The operating conditions of a compact, high-neutron-wall-loading fusion reactor severely limit the choices for structural, shield, insulator, and breeder materials. In particular the response of plasma-facing materials to radiation, thermal and pressure stresses, and their compatibility with coolants are of primary concern. Material selection issues are investigated for the compact, high mass-power-density TITAN-I reactor design study. In this paper the major findings regarding material performance are discussed. The retention of mechanical strength at relatively high temperatures, low thermal stresses, and compatibility with liquid lithium make vanadium-base alloys a promising material for structural components. Based on limited data, the thermal creep behaviour of V3TiISi and V15Cr5Ti alloys is approximated using the modified minimum committment method. In addition, the effects of irradiation and helium generation are superimposed on the creep behavior of V3Ti1Si. Coolant compatibility issues are investigated. The liquid lithium compatibility of the two vanadium alloys, V15Cr5Ti and V3Ti1Si, are compared, and the latter was chosen as the primary structural-material candidate for the liquid-lithium-cooled TITAN-I reactor. Electrically insulating materials, capable of operating at high temperatures are necessary throughout the fusion reactor device. Electrical insulator-material issues of concern include irradiation induced swelling and conductivity. Both issues are investigated and operating temperatures for minimum swelling and dielectric breakdown strength are identified for spinel (MgAI2O4).

References (50)

  • D.L. Smith et al.

    Blanket comparison and selection study-Final Report

    Argonne National Laboratory report ANL/FPP-84-1

    (1984)
  • D.N. Braski

    The effect of neutron irradiation on the tensile properties and microstructure of several vanadium alloys

  • B.A. Loomis et al.
  • D.K. Sze, P. Gierszewski, and T. Bartlitt, TITAN Tritium Issues, Fusion Engrg. Des. (to be...
  • I. Lemay

    Principles of Mechanical Metallurgy

  • S.S. Manson et al.

    NASA report TM.X-52999

    (1971)
  • N.M. Ghoniem et al.

    Assessment of ferritic steels for steady state fusion reactors

  • D.L. Harrod et al.

    Mechanical properties of vanadium and vanadium-base alloys

    Int. Met. Rev.

    (1980)
  • ASME Boiler and Pressure Vessel Code, 1977

    Code Cases-Nuclear Components, 1977 edition

    (1977)
  • D.N. Braski

    The effects of helium on the tensile properties of several vanadium Alloys

  • M.S. Freed et al.

    Nuclear Propulsion Program Quarterly Report

    Pratt and Whitney Aircraft Division of United Aircraft Corp. report PWAC-355

    (1961)
  • J.R. DiStefano

    Oak Ridge National Laboratory report ORNL-3551

    (1964)
  • D.L. Smith et al.
  • R.L. Ammon

    Vanadium and vanadium-alloy compatibility behaviour with lithium and sodium at elevated temperatures

    Int. Metals Rev.

    (1980)
  • Cited by (24)

    • Tailorable nano MgO.xAl<inf>2</inf>O<inf>3</inf> spinel compositions along line of homogeneity via gel combustion route: Influence on phase evolution

      2019, Materials Chemistry and Physics
      Citation Excerpt :

      It is a stable oxide compound of spinel group exhibiting combination of good properties: high melting point (2135 °C), low thermal conductivity, good thermal shock resistance, chemical inertness, and good mechanical strength both at room temperature as well as high temperature also. Owing to these excellent combinations of features MgAl2O4 is widely applicable to refractory materials [1], catalyst supports [2], humidity sensors [3], nuclear techniques [4], insulating materials [5], military applications (domes, armor materials, etc.) [6,7], dentistry [8], and so on. Its photocatalytic degradation property [9] can be utilized as a treatment for the industrial effluents containing different toxic dye materials before releasing them into environment.

    • DC conductivity and AC impedance of Mn doped magnesia alumina spinel (MgAl<inf>2-2x</inf>Mn<inf>2x</inf>O<inf>4</inf>) over a large temperature range

      2019, Journal of the European Ceramic Society
      Citation Excerpt :

      Magnesia alumina oxide (MgAl2O4) spinel (MAS, AB2O4,) has been widely researched by scientists during the past few decades, due to its many excellent properties such as high melting point (2408 K), low theoretical density (3.58 g/cm3), superior hardness, considerable mechanical strength at high temperature and good resistance against chemical corrosion [1–3]. Traditional MAS is often used as refractory material [4], transparent armor [5], insulating material [6], neutron diffraction resistance [7], catalyst-catalyst support [8] and thermal barrier coating [9] in terms of its basic properties. Further, its practical applications also play a significant role in modern society.

    • Recycling of LCW produced form water plants for synthesizing of nano FeO(OH), Al(OH)<inf>3</inf>, and layered double hydroxide: Effect of heat-treatment

      2018, Ceramics International
      Citation Excerpt :

      One of the most interested applications of LDHs is the ceramic field. Their applications in ceramics produce important category called spinels which have interested properties and many applications such as structural and refractory materials as well as electronics, fusion reactors, optical devises and medical applications [27–38]. The goal of the current work is recycling of liquid waste concentrate produced from water plants for production of interested materials as nano iron oxide hydroxide FeO(OH), aluminum hydroxide A1(OH)3, and magnesium-aluminum layered double hydroxide Mg-Al-LDH, for different applications.

    • Magnesium aluminate planar waveguides fabricated by C-ion implantation with different energies and fluences

      2015, Nuclear Instruments and Methods in Physics Research, Section B: Beam Interactions with Materials and Atoms
      Citation Excerpt :

      This structural similarity could explain the reason of the high hardness typical of this material [7]. Because of its good resistance to radiation-induced swelling and strength degradation, magnesium aluminate is a potential fusion reactor power core insulating material [6]. However, this material has a higher IR absorption edge and required light transmission in the wavelength range of 2–5.5 μm and is now being replaced by ZnS, sapphire, AION, traditional alumina, and lanthanum niobate ceramics in applications including laser ignitors, windows for UV lithography, barcode scanners, spacecraft, watches, and night-vision systems [2,8–14].

    View all citing articles on Scopus
    1

    Present address: On assignment from Culham Laboratory, Abington, Oxfordshire, UK

    2

    Present address: Oak Ridge National Laboratory, Oak Ridge, TN 37831, USA.

    See p. 69 in this issue.

    View full text