ISSN:
0947-5117
Keywords:
Chemistry
;
Polymer and Materials Science
Source:
Wiley InterScience Backfile Collection 1832-2000
Topics:
Mechanical Engineering, Materials Science, Production Engineering, Mining and Metallurgy, Traffic Engineering, Precision Mechanics
Description / Table of Contents:
The corrosion behaviour of lead and lead alloys in sulphuric acid solutionsLong-time corrosion tests have been carried out in sulphuric acid solutions of different concentration (up to 70 per cent.) and at different temperatures (up to boiling point), using specimens of fine lead, copper fine lead and different types of hard lead. The only noticeable, and noticeably different, corrosion rates were encountered at temperatures above 100% c.In the medium 'and high concentration range, fine lead and, to a lesser extent, even copper fine lead were increasingly affected by corrosion; in agreement with published data, the corrosion values especially of fine lead showed a marked scatter and some of them were extremely high. Hard lead with 1.5 to 6 percent. antimony was less affected by the highly concentrated acids; but low-alloyed hard lead, showed, a maximum corrosion, rate in diluted acid. The comparatively highest resistance was shown by hard lead with 6 percent. antimony which showed noticeable corrosion under the influence of the strongest acid only (70 percent. H2SO4). A particularly high resistance in this acid was shown by a copper hard lead (0.6 percent antimony).Boiling tests on a minor technical scale with steel pots with homogeneous internal lead coating revealed a surprisingly high corrosion resistance of the lead coating, which consisted of copper lead, even in 70 percent acid heated to 150° C; such resistance was not to be expected from the preceding tests and exceeded that encountered with hard lead (6 percnt. SB) A chemical analysis showed that copper lead coating must, during manufacture, have absorbed tin, and subsequent tests showed that a small admixture of tin results in quite a considerable increase in the corrosion resistance of the copper lead. An increased copper content, too, had a favourable effect but only in the strongest acid.Finally, a number of tests were carried out in order to ascertain the influence, on the corrosion performance of some types of lead, of an admixture of nitric acid to the sulphuric acid (70 percent.). In all cases, the admixture had the effect of reducing the corrosion rate, especially with copper lead.The conclusions to be drawn from the test results in regard to corrosion tests and work practice are discussed.
Notes:
Langzeit-Korrosionsversuche wurden in Schwefelsäurelösungen verschiedener Konzentration (bis 70 %) und Temperatur (bis Siedepunkt) an Proben aus Feinblei, Kupferfeinblei und verschiedenen Hartbleisorten durchgeführt. Dabei ergaben sich merkliche und unterschiedlich große Korrosionsgeschwindigkeiten nur bei Temperaturen oberhalb 100° C.Feinblei und in geringerem Maß auch Kupferfeinblei wurden im mittleren und höheren Konzentrationsbereich zunehmend stärker korrodiert, wobei - in Übereinstimmung mit Literaturangaben - namentlich bei Feinblei stark streuende und z. T. außerordentlich hohe Korrosionswerte erhalten wurden. Hartblei mit 1,5 bis 6 % Sb wurde von den stärkeren Säuren weniger angegriffen, dagegen zeigte niedriglegiertes Hartblei ein Korrosionsmaximum in verdünnter Säure. Verhältnismäßig am beständigsten erwies sich Hartblei mit 6% Sb, das nur in der stärksten Säure (70 % H2SO4)merklich korrodiert wurde. In dieser war ein CU-Hartblei (0,6 % Sb) besonders beständig.Kleintechnische Kochversuche an innen homogenverbleiten Stahltöpfen ergaben ein überraschend gutes Korrosionsverhalten der aus Kupferblei bestehenden Verbleiung auch in 15O° C heißer 70°/oiger Säure das nach den vorhergehenden Versuchen nicht zu erwarten war und dasjenige der mit Hartblei (6% Sb) ausgekleideten Töpfe übertraf. Durch Analysen wurde festgestellt, daß die Kupferverbleiung offenbar bei der Herstellung Zinn aufgenommen hatte, und durch Versuche wurde gezeigt, daß ein geringer Zinngehalt die Beständigkeit des Kupferbleis ganz beträchtlich verbessert. Auch ein erhöhter Cu-Gehalt wirkte sich günstig aus, jedoch nur in der stärksten Säure.Schließlich wurde in einigen Versuchen der Einfluß eines Salpetersäurezusatzes zur Schwefelsäure (70%) auf das Korrosionsverhalten einiger Bleisorten geprüft. In allen Fällen verminderte er die Korrosion, besonders stark bei Kupferblei.Die aus den Versuchsergebnissen sich ergebenden Folgerungen für die Korrosionsprüfung und Betriebspraxis werden erörtert.
Additional Material:
14 Ill.
Type of Medium:
Electronic Resource
URL:
http://dx.doi.org/10.1002/maco.19640150706
Permalink