Bibliothek

feed icon rss

Ihre E-Mail wurde erfolgreich gesendet. Bitte prüfen Sie Ihren Maileingang.

Leider ist ein Fehler beim E-Mail-Versand aufgetreten. Bitte versuchen Sie es erneut.

Vorgang fortführen?

Exportieren
  • 1
    Digitale Medien
    Digitale Medien
    Westerville, Ohio : American Ceramics Society
    Journal of the American Ceramic Society 83 (2000), S. 0 
    ISSN: 1551-2916
    Quelle: Blackwell Publishing Journal Backfiles 1879-2005
    Thema: Maschinenbau , Physik
    Notizen: High-pressure sintering behavior in the B6O–c-BN system was investigated using in-laboratory-synthesized B6O and commercially available c-BN powders (with an average grain size of 0.5, 3, or 6 μm). No reaction occurred between the two components under the high-pressure (4–6 GPa) and high-temperature (1500°–1800°C) conditions that have been investigated. Well-dispersed, sintered B6O–x(c-BN) composites (wherex= 0–60 vol%) of almost-full density were prepared by sintering at a pressure of 6 GPa and temperature of 1800°C for 20 min. The maximum Vickers microhardness (46 GPa) of these composites was attained by adding 40 vol%c-BN with an average grain size of 0.5 μm. The fracture toughness of these composites increased as the c-BN content increased; the maximum fracture toughness (1.5–1.8 MPa.m1/2) was observed for x= 40–60 vol%. Crack deflection along the B6O–c-BN grain boundary contributed to increasing the fracture toughness.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 2
    Digitale Medien
    Digitale Medien
    Westerville, Ohio : American Ceramics Society
    Journal of the American Ceramic Society 80 (1997), S. 0 
    ISSN: 1551-2916
    Quelle: Blackwell Publishing Journal Backfiles 1879-2005
    Thema: Maschinenbau , Physik
    Notizen: A dense Ca(Ti0.75Fe0.25)O3−α (Ca(Ti,Fe)O3) film, which is a mixed conductor of oxide ions and electrons/holes, was prepared on a porous CaTiO3 substrate by a spin-coating method. The calcined Ca(Ti,Fe)O3 powder with 2–3 μm grain sizes was mixed with a dispersant in ethanol to form the slurry for spin coating. A uniform Ca(Ti,Fe)O3 green film was obtained at 1000–1500 rpm on the rotating porous CaTiO3 substrate, which had an average pore diameter of a few micrometers. The optimum sintering conditions for the spin-coated films were a soaking temperature of 1235°C and a holding time of 2 h, in air. A dense, sintered Ca(Ti,Fe)O3 film }20–50 μm thick was prepared by repeating the coatingsintering process. The gas-tight film prepared on the porous substrate exhibited higher electrochemical permeation of oxygen at an operating temperature of 1000°C compared with that of thicker, sintered Ca(Ti,Fe)O3 disks.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 3
    Digitale Medien
    Digitale Medien
    Westerville, Ohio : American Ceramics Society
    Journal of the American Ceramic Society 80 (1997), S. 0 
    ISSN: 1551-2916
    Quelle: Blackwell Publishing Journal Backfiles 1879-2005
    Thema: Maschinenbau , Physik
    Notizen: A thick diamond film was coated using two-stage microwave plasma CVD in the COH, system on a pretreated silicon nitride substrate for a cutting tool. The effects of acid treatment and microflawing treatment of the substrate on adherence of the film and cutting performance were investigated as well as the effects of two-stage CVD conditions. The combination of substrate pretreatment in a hot, strong acid solution of HF and HNO3 and subsequent ultrasonic microflawing pretreatment with diamond grains resulted in the anchored deposition of CVD diamond into the micropores in the silicon nitride substrate. An excellent adherence of the diamond film to the substrate was attained by the two-stage CVD, which consists of a first CVD of fine diamond grains into the micropores and a second higher rate CVD of thick diamond film (thickness 〉30 pm). A dense layer composed of diamond-like carbon and silicon nitride was formed deep in the boundary region of the substrate during long CVD treatment. Long tool life of the silicon nitride chip coated with a thick diamond film was verified by a milling test using Al-20 wt% Si alloy as the work material.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 4
    Digitale Medien
    Digitale Medien
    Springer
    Journal of applied electrochemistry 3 (1973), S. 65-72 
    ISSN: 1572-8838
    Quelle: Springer Online Journal Archives 1860-2000
    Thema: Chemie und Pharmazie , Elektrotechnik, Elektronik, Nachrichtentechnik
    Notizen: Abstract The ionic conduction in sintered oxides of the system Bi2O3-WO3 was investigated by measuring conductivities and ion transference numbers under various conditions. The ion transference number was measured by an oxygen concentration cell employing the specimen tablet as the electrolyte. It was found that a compound 3Bi2O3 WO3 and its solid solution were high oxide ion conductors, the conductivities of which were about one order of magnitude higher than those of the well-known oxide ion conductors such as stabilized zirconias. In contrast to pure Bi2O3 which is a completely electronic conductor below 730°C, these materials showed high oxide ion conduction even below 700°C accompanied by little electronic conduction. 3Bi2O3 WO3 has the face centered cubic structure, probably of the fluorite type, and the oxide ion conduction was thought to be attributed to the migration of oxide ion vacancies in the crystal.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 5
    Digitale Medien
    Digitale Medien
    Springer
    Journal of materials science 27 (1992), S. 5745-5750 
    ISSN: 1573-4803
    Quelle: Springer Online Journal Archives 1860-2000
    Thema: Maschinenbau
    Notizen: Abstract Microtopographical variations of {111} and {100} crystal surfaces of single-crystalline diamond grown by microwave-plasma chemical vapour deposition of the CO-H2 reactant system were examined using scanning electron microscopy. A layer-by-layer epitaxial growth process was observed on both crystal surfaces. A number of epitaxial two-dimensional nuclei were formed at random on {111} surfaces, where small triangular growth layers spread with the same orientations as the outline of the original {111} basal plane. These spreading layers were found to leave an inverse triangular pit (so-called trigon) pattern as they joined each other. On the other hand, square growth layers spread in parallel directions to {100} basal plane, and they stacked in the 〈100〉 directions to form a pyramidal growth hillock.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 6
    ISSN: 1573-4803
    Quelle: Springer Online Journal Archives 1860-2000
    Thema: Maschinenbau
    Notizen: Abstract Platinum-dispersed carbon was synthesized by pressure pyrolysis of divinylbenzenebis (2-allylphenyl)platinum (APPt) and phenylacetylene-APPt at 550 °C and 125 MPa. The crystallinity of platinum dispersed in the carbon matrix synthesized from phenylacetylene(PA)-APPt was higher than that from divinylbenzene(DVB)-APPt. Platinum particles less than 60 nm were dispersed in the carbon matrix synthesized from DVB-APPt at 550 °C and 125 MPa. The carbon matrix formed from PA-APPt contained platinum particles of about 120 nm. The specific area of platinum-dispersed carbon synthesized at 550 °C and 125 MPa increased on subsequent heat treatments in argon, and reached 90 m2 g−1 after heat treatment at 800 °C for 1 h. The activity of platinum-dispersed carbon for the hydrogenation of cyclohexene increased with increasing specific area. Platinum-dispersed carbon formed from DVBAPPt was more active for hydrogenation reaction than that from PA-APPt. The highly active platinum-dispersed carbon could be synthesized from DVB-APPt at 520 °C. The surface area reached 154 m2 g−1 after heat treatment at 800 °C.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 7
    ISSN: 1573-8663
    Schlagwort(e): proton conduction ; perovskite ; scandium oxide ; concentration cell ; electrochemical pump
    Quelle: Springer Online Journal Archives 1860-2000
    Thema: Elektrotechnik, Elektronik, Nachrichtentechnik , Maschinenbau
    Notizen: Abstract Ionic transport properties of perovskite-type oxides based on LnScO3, Ln1- xCaxScO3-α (Ln=La, Nd, Sm and Gd) and LaSc1-xMgxO3-α were studied using an electrochemical method at elevated temperatures. Conductivity in these oxide systems increased by more than three orders of magnitude upon doping with divalent atoms such as Ca or Mg. However, when x≥0.1, conductivities are almost independent of x in La1- xCaxScO_3-α and LaSc1- xMgxO3-α. Gd0.9Ca0.1ScO3-α showed lower conductivity than Ln1-xCaxScO3-α (Ln=La, Nd and Sm). Protonic conduction in these oxides under hydrogen containing atmospheres was confirmed by emf measurements of hydrogen concentration cells and by electrochemical hydrogen pumping using these oxides as a diaphragm. In LaSc1-xMgxO3-α the transport number of protons under hydrogen containing atmosphere was unity, suggesting that electronic conduction never became dominant, even under strong reducing conditions. Under condition of high oxygen partial pressure, the transport number of ions was less than 0.1, suggesting that the majority conductive carriers under such conditions were holes.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
Schließen ⊗
Diese Webseite nutzt Cookies und das Analyse-Tool Matomo. Weitere Informationen finden Sie hier...