Library

feed icon rss

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
  • 1
    Electronic Resource
    Electronic Resource
    Bognor Regis [u.a.] : Wiley-Blackwell
    Journal of Polymer Science Part B: Polymer Physics 36 (1998), S. 1557-1566 
    ISSN: 0887-6266
    Keywords: polyesters ; PET ; PEN ; PEI ; 13C NMR ; dynamics ; nuclear relaxation times ; gas diffusion ; Physics ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology , Physics
    Notes: The dynamics of amorphous aromatic polyesters consisting of poly(ethylene terephthalate) (PET), poly(ethylene isophthalate) (PEI), and poly(ethylene 2,6-naphthalenedicarboxylate) (PEN) has been investigated by means of solid state CPMAS 13C NMR. Proton T2, 13C T1ρ, and proton T1ρ decays have been measured in particular, and the experimental data fitted to suitable model functions to determine best relaxation parameters. The fitting results show for proton T2 and 13C T1ρ measurements the presence of two components with different relaxation times and intensities, arising from different motional domains. The proton T1ρ, on the contrary, shows a single component which limits the dimensions of the two regions to less than 20 Angstroms. The dependence of 13C T1ρ values on two different irradiating field strengths (H1 = 38 KHz, H1 = 60 KHz) allowed the assignment of each component to relatively rigid and mobile regions. By comparing the three polymers we observe that PEN and PEI have a similar relaxation behavior, while a higher fraction of mobile components was found for PET. These differences are believed to arise mainly from local motions of the aromatic rings. The relaxation measurements have been evaluated to suggest a correspondence to O2 and CO2 gas permeabilities in PET, PEI, and PEN. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1557-1566, 1998
    Additional Material: 7 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
  • 2
    Electronic Resource
    Electronic Resource
    Bognor Regis [u.a.] : Wiley-Blackwell
    Journal of Polymer Science Part A: Polymer Chemistry 36 (1998), S. 2119-2126 
    ISSN: 0887-624X
    Keywords: stereospecific polymerization ; isotactic polystyrene ; nickel catalysts ; methylaluminoxane ; Chemistry ; Polymer and Materials Science
    Source: Wiley InterScience Backfile Collection 1832-2000
    Topics: Chemistry and Pharmacology
    Notes: Polymerization of styrene using catalytic systems based on nickel derivatives and methylaluminoxane (MAO) was studied. Among tested catalysts, nickel bis(acetylacetonate) and nickel dichloride show the maximum activity. Bis(phosphine)nickel dichlorides exhibit lower activity, depending on the nature of the phosphine ligand. Polymer yields decrease by lowering the catalyst concentration, by increasing the reaction temperature, or by carrying out the polymerization in a polar donor solvent. Weight average molecular weight of most of the prepared polystyrenes ranges from 9000 to 25,000, with polydispersity indexes of 1.6-3.8. However, polystyrene prepared in dioxane solvent exhibits a small fraction of very high molecular weight (about 140,000). From NMR analysis, the products seem generally to be constituted of two polymers with different steric microstructure: atactic polystyrene and partially isotactic polystyrene (ca. 75-85% meso diads). Catalytic site specificity is correlated with the type of nickel ligand, while the effect of reaction temperature is less defined. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2119-2126, 1998
    Additional Material: 1 Ill.
    Type of Medium: Electronic Resource
    Library Location Call Number Volume/Issue/Year Availability
    BibTip Others were also interested in ...
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...