Bibliothek

feed icon rss

Ihre E-Mail wurde erfolgreich gesendet. Bitte prüfen Sie Ihren Maileingang.

Leider ist ein Fehler beim E-Mail-Versand aufgetreten. Bitte versuchen Sie es erneut.

Vorgang fortführen?

Exportieren
Filter
  • biofilm  (10)
  • biomass yield  (3)
  • kinetics  (3)
  • 1
    Digitale Medien
    Digitale Medien
    Springer
    Antonie van Leeuwenhoek 60 (1991), S. 235-256 
    ISSN: 1572-9699
    Schlagwort(e): biomass yield ; chemotrophic growth ; Gibbsenergy dissipation ; thermodynamic efficiencies
    Quelle: Springer Online Journal Archives 1860-2000
    Thema: Biologie
    Notizen: Abstract A new, generally applicable, thermodynamically based method is proposed to provide an estimation of the biomass yield on arbitrary organic and inorganic substrates. Aerobic, anaerobic, denitrifying growth systems with and without reversed electrontransport are covered. The biomass yield can be estimated with only 15% error in a very wide range of microbial growth systems and biomass yields (0.01–0.80 C-mol/(C)-mol). This method is based on the use of ‘Gibbs energy dissipared per C-mol produced biomass’ (designated as D infS sup01 /rAx) as the central parameter. Moreover the insufficiency of other methods based on YATP, YAve, ŋ0, YC and enthalpy or Gibbs energy efficiencies is shortly discussed. Also it appeared to be possible to understand the obtained correlation of D infS sup01 /rAx in general biochemical terms.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 2
    Digitale Medien
    Digitale Medien
    New York, NY [u.a.] : Wiley-Blackwell
    Biotechnology and Bioengineering 53 (1997), S. 168-178 
    ISSN: 0006-3592
    Schlagwort(e): airlift reactor ; BAS reactor ; biofilm ; nitrification ; nitrite ; oxygen transfer ; residence time ; Chemistry ; Biochemistry and Biotechnology
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Biologie , Werkstoffwissenschaften, Fertigungsverfahren, Fertigung
    Notizen: The biofilm airlift suspension (BAS) reactor can treat wastewater at a high volumetric loading rate combined with a low sludge loading. Two BAS reactors were operated, with an ammonium load of 5 kg N/(m3 d), in order to study the influence of biomass and oxygen concentration on the nitrification process. After start-up the nitrifying biomass in the reactors gradually increased up to 30 g VSS/L. Due to this increased biomass concentration the gas-liquid mass transfer coefficient was negatively influenced. The resulting gradual decrease in dissolved oxygen concentration (over a 2-month period) was associated with a concomitantly nitrite build-up. Short term experiments showed a similar relation between dissolved oxygen concentration (DO) and nitrite accumulation. It was possible to obtain full ammonium conversion with approximately 50% nitrate and 50% nitrite in the effluent. The facts that (i) nitrite build up occurred only when DO dropped, (ii) the nitrite formation was stable over long periods, and (iii) fully depending on DO levels in short term experiments, led to the conclusion that it was not affected by microbial adaptations but associated with intrinsic characteristics of the microbial growth system. A simple biofilm model based on the often reported difference of oxygen affinity between ammonium and nitrite oxydizers was capable of adequately describing the phenomena.Measurements of biomass density and concentration are critical for the interpretation of the results, but highly sensitive to sampling procedures. Therefore we have developed an independent method, based on the residence time of Dextran Blue, to check the experimental methods. There was a good agreement between procedures.The relation between biomass concentration, oxygen mass transfer rate and nitrification in a BAS reactor is discussed. © 1997 John Wiley & Sons, Inc.
    Zusätzliches Material: 6 Ill.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 3
    Digitale Medien
    Digitale Medien
    New York, NY [u.a.] : Wiley-Blackwell
    Biotechnology and Bioengineering 53 (1997), S. 397-405 
    ISSN: 0006-3592
    Schlagwort(e): airlift reactor ; biofilm ; biofilm detachment ; control biofilm formation ; heterotrophic layer ; hydraulic retention time ; nitrification ; oxygen diffusion limitation ; Chemistry ; Biochemistry and Biotechnology
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Biologie , Werkstoffwissenschaften, Fertigungsverfahren, Fertigung
    Notizen: A Biofilm Airlift Suspension (BAS) reactor was operated with nitrifying biofilm growth and heterotrophic suspended growth, simultaneously converting ammonium and acetate. Growth of heterotrophs in suspension decreases the diffusion limitation for the nitrifiers, and enlarges the nitrifying capacity of a biofilm reactor. Neither nitrifiers nor heterotrophs suffer from additional oxygen diffusion limitation when the heterotrophs grow in suspension. Control of the location of heterotrophic growth, either in suspension or in biofilms over the nitrifying biofilms, was possible by manipulation of the hydraulic retention time. A time delay for formation and disappearance of the heterotrophic biofilms of 10 to 15 days was observed. Surprisingly, it was found that in the presence of the heterotrophic layers the maximum specific activity on ammonia of the nitrifying biofilms increased. The reason for the increase in activity is unknown. The effect of heterotrophic biofilm formation on oxygen diffusion limitation for the nitrifiers is discussed. Some phenomena compensating the increased mass transfer resistance due to the growth of a heterotrophic layer are also presented. © 1997 John Wiley & Sons, Inc. Biotechnol Bioeng 53: 397-405, 1997.
    Zusätzliches Material: 6 Ill.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 4
    Digitale Medien
    Digitale Medien
    New York, NY [u.a.] : Wiley-Blackwell
    Biotechnology and Bioengineering 46 (1995), S. 258-269 
    ISSN: 0006-3592
    Schlagwort(e): biofilm ; detachment ; abrasion ; breakage ; airlift reactor ; hydrodynamics ; Chemistry ; Biochemistry and Biotechnology
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Biologie , Werkstoffwissenschaften, Fertigungsverfahren, Fertigung
    Notizen: In three-phase internal loop airlift reactors, the detachment of biomass from suspended biofilm pellets in the presence of bare carrier particles was investigated under nongrowth conditions. The detachment rate was dominated by collisions between bare carrier particles and biofilm pellets. The concentration of bare carrier particles and the carrier roughness strongly influenced the detachment rate. A change in flow regime from bubbling to slug flow considerably increased the detachment rate. Otherwise, the superficial gas velocity did not directly affect the detachment rate. The influence of particle size was not clear. The bottom clearance did not affect the detachment rate within the tested range. Other aspects of reactor geometry might be important. The main detachment processes were abrasion and breakage of biofilm pellets. During the detachment process, two phases could be distinguished. In the first phase the detachment was relatively high, and both breakage and abrasion of biofilm pellets occurred. During the second phase, breakage dominated and the detachment rate was lower. The two-phase behavior is explained by differences in strength between the inner and outer biofilm layers, possibly caused by variations in local growth rates during biofilm formation. Differences in growth history might also explain the various detachment rates observed with different biofilm batches. © 1995 John Wiley & Sons, Inc.
    Zusätzliches Material: 9 Ill.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 5
    Digitale Medien
    Digitale Medien
    New York, NY [u.a.] : Wiley-Blackwell
    Biotechnology and Bioengineering 48 (1995), S. 681-698 
    ISSN: 0006-3592
    Schlagwort(e): stoichiometry ; biomass yield ; product yield ; metabolic fluxes ; Saccharomyces cerevisiae ; Candida utilis ; Chemistry ; Biochemistry and Biotechnology
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Biologie , Werkstoffwissenschaften, Fertigungsverfahren, Fertigung
    Notizen: Using available biochemical information, metabolic networks have been constructed to describe the biochemistry of growth of Saccharomyces cerevisiae and Candida utilis on a wide variety of carbon substrates. All networks contained only two fitted parameters, the P/O ratio and a maintenance coefficient. It is shown that with a growth-associated maintenance coefficient, K, of 1.37 mol ATP/ C-mol protein for both yeasts and P/O ratios of 1.20 and 1.53 for S. cerevisiae and C. utilis, respectively, measured biomass yields could be described accurately. A metabolic flux analysis of aerobic growth of S. cerevisiae on glucose/ethanol mixtures predicted five different metabolic flux regimes upon transition from 100% glucose to 100% ethanol. The metabolic network constructed for growth of S. cerevisiae on glucose was applied to perform a theoretical exercise on the overproduction of amino acids. It is shown that theoretical operational product yield values can be substantially lower than calculated maximum product yields. A practical case of lysine production was analyzed with respect to theoretical bottlenecks limiting product formation. Predictions of network-derived irreversibility limits for Ysp (μ) functions were compared with literature data. The comparisons show that in real systems such irreversibility constraints may be of relevance. It is concluded that analysis of metabolic network stoichiometry is a useful tool to detect metabolic limits and to guide process intensification studies. © 1995 John Wiley & Sons, Inc.
    Zusätzliches Material: 7 Ill.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 6
    Digitale Medien
    Digitale Medien
    New York, NY [u.a.] : Wiley-Blackwell
    Biotechnology and Bioengineering 39 (1992), S. 833-858 
    ISSN: 0006-3592
    Schlagwort(e): biomass yield ; chemotrophic growth ; Gibbs energy dissipation ; thermodynamic efficiencies ; energy convertor ; Chemistry ; Biochemistry and Biotechnology
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Biologie , Werkstoffwissenschaften, Fertigungsverfahren, Fertigung
    Notizen: Correlations for the prediction of biomass yields are valuable, and many proposals based on a number of parameters (YATP, YAve, ηo, Yc, Gibbs energy efficiencies, and enthalpy efficiencies) have been published. This article critically examines the properties of the proposed parameters with respect to the general applicability to chemotrophic growth systems, a clear relation to the Second Law of Thermodynamics, the absence of intrinsic problems, and a requirement of only black box information. It appears that none of the proposed parameters satisfies all these requirements. Particularly, the various energetic efficiency parameters suffer from major intrinsic problems. However, this article will show that the Gibbs energy dissipation per amount of produced biomass (kJ/C-mod) is a parameter which satisfies the requirements without having intrinsic problems. A simple correlation is found which provides the Gibbs energy dissipation/C-mol biomass as a function of the nature of the C-source (expressed as the carbon chain length and the degree of reduction). This dissipation appears to be nearly independent of the nature of the electron acceptor (e.g., O2, No3-, fermentation). Hence, a single correlation can describe a very wide range of microbial growth systems. In this respect, Gibbs energy dissipation is much more useful than heat production/C-mol biomass, which is strongly dependent on the electron acceptor used. Evidence is presented that even a net heat-uptake can occur in certain growth systems.The correlation of Gibbs energy dissipation thus obtained shows that dissipation/C-mol biomass increases for C-sources with smaller chain length (C6 → C1), and increases for both higher and lower degrees of reduction than 4. It appears that the dissipation/C-mol biomass can be regarded as a simple thermodynamic measure of the amount of biochemical “work” required to convert the carbon source into biomass by the proper irreversible carbon-carbon coupling and oxidation/reduction reactions. This is supported by the good correlation between the theoretical ATP requirement for biomass formation on different C-sources and the dissipation values (kJ/C-mol biomass) found. The established correlation for the Gibbs energy dissipation allows the prediction of the chemotrophic biomass yield on substrate with an error of 13% in the yield range 0.01 to 0.80 C-mol biomass/(C)-mol substrate for aerobic/anaerobic/denitrifying growth systems.
    Zusätzliches Material: 8 Ill.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 7
    Digitale Medien
    Digitale Medien
    New York, NY [u.a.] : Wiley-Blackwell
    Biotechnology and Bioengineering 44 (1994), S. 867-879 
    ISSN: 0006-3592
    Schlagwort(e): biofilm ; microbeads ; solids retention time ; airlift reactor ; particulates ; Chemistry ; Biochemistry and Biotechnology
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Biologie , Werkstoffwissenschaften, Fertigungsverfahren, Fertigung
    Notizen: Fluorescent microparticles were used as tracer beads to measure the dynamics of solids in spherical biofilms in a biofilm airlift suspension reactor. Attachment to, release from, and penetration into the biofilms of the tracer beads were measured. The coverage of the biofilm surface was low and the steady state particle concentration on the surface was dependent on the biofilm surface characteristics. The measured attachment rate constant was identical in both experiments and appeared to be determined by the hydrodynamic conditions in the turbulent reactor. The attachment rate was much faster than the release rate of the tracer beads and, therefore, the solidsretention time in the biofilm particle is not due to a simple reversible adsorption-desorption process. The heterogeneity of the distribution oftracer beads on different sectors on the biofilm surface decreased duringthe attachment period. Due to random detachment processes the heterogeneity of the tracer bead distribution increased during the release periodThe tracer beads quickly penetrated into the biofilm and became distributed throughout the active layer of the biofilm. The observed penetration into biofilms, the nonuniform distribution on the biofilm surface, and the fast uptake and slow release of tracer beads cannot be described by a simple model based on a reversible adsorption-desorption mechanism, nor withexisting biofilm models. These biofilm models, which balance growth and advection assuming a uniform biofilm with a homogeneous surface, are inadequate for the description of the observed solids retention time in biofilms. Therefore, a new concept of biofilm dynamics is proposed, in which formation of cracks and fissures, which are rapidly filled with growing biomass, combined with nonuniform local detachment, explains the observed fast penetration into the biofilm of tracer beads, the long residence time, and the nonuniform distibution of fluorescent microparticles. © 1994 John Wiley & Sons, Inc.
    Zusätzliches Material: 11 Ill.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 8
    Digitale Medien
    Digitale Medien
    New York, NY [u.a.] : Wiley-Blackwell
    Biotechnology and Bioengineering 44 (1994), S. 595-608 
    ISSN: 0006-3592
    Schlagwort(e): biofilm ; aerobic waste water treatment ; airlift reactor ; waste water ; Chemistry ; Biochemistry and Biotechnology
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Biologie , Werkstoffwissenschaften, Fertigungsverfahren, Fertigung
    Notizen: In this article, the conditions for aerobic biofilm formation on suspended particles, the dynamics of biofilm formation, and the biomass production during the start-up of a Biofilm Airlift Suspension reactor (BAS reactor) have been studied. The dynamics of biofilm formation during start up in the biofilm airlift suspension reactor follows three consecutive stages: bare carrier, microcolonies or patchy biofilms on the carrier, and biofilms completely covering the carrier. The effect of hydraulic retention time and of substrate loading rate on the formation of biofilms were investigated. To obtain in a BAS reactor a high biomass concentration and predominantly continuous biofilms, which completely surround the carrier, the hydraulic retention time must be shorter than the inverse of the maximum growth rate of the suspended bacteria. At longer hydraulic retention times, a low amount of attached biomass can be present on the carrier material as patchy biofilms. During the start-up at short hydraulic retention times the bare carrier concentration decreases, the amount of biomass per biofilm particle remains constant, and biomass increase in the reactor is due to increasing numbers of biofilm particles. The substrate surface loading rate has effect only on the amount of biomass on the biofilm particle. A higher surface load leads to a thicker biofilm.A strong nonlinear increase of the concentration of attached biomass in time was observed. This can be explained by a decreased abrasion of the biofilm particles due to the decreasing concentration of bare carriers. The detachment rate per biofilm area during the start-up is independent of the substrate loading rate, but depends strongly upon the bare carrier concentration.The Pirt-maintenance concept is applicable to BAS reactors. Surplus biomass production is diminished at high biomass concentrations. The average maximal yield of biomass on substrate during the experiments presented in this article was 0.44 ± 0.08 C-mol/C-mol, the maintenance value 0.019 ± 0.012 C-mol/(C-mol h). The lowest actual biomass yield measured in this study was 0.15 C-mol/C-mol. © 1994 John Wiley & Sons, Inc.
    Zusätzliches Material: 11 Ill.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 9
    Digitale Medien
    Digitale Medien
    New York, NY [u.a.] : Wiley-Blackwell
    Biotechnology and Bioengineering 47 (1995), S. 277-287 
    ISSN: 0006-3592
    Schlagwort(e): phosphorus removal ; biological ; kinetics ; metabolic model ; polyphosphate ; PHB ; glycogen ; batch reactor, sequenced ; Chemistry ; Biochemistry and Biotechnology
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Biologie , Werkstoffwissenschaften, Fertigungsverfahren, Fertigung
    Notizen: A structured metabolic model is developed that describes the stoichiometry and kinetics of the biological P removal process. In this approach all relevant metabolic reactions underlying the metabolism, considering also components like adenosine triphosphate (ATP) and nic-otinamide-adenine dinucleotide (NADH2) are describedbased on biochemical pathways. As a consequence of the relations between the stoichiometry of the metabolic reactions and the reaction rates of components, the required number of kinetic relations to describe the process is reduced. The model describes the dynamics of the storage compounds which are considered separately from the active biomass. The model was validated in experiments at a constant sludge retention time of 8 days, over the anaerobic and aerobic phases in which the external oncentrations as well as the internal fractions of the relevant components involved in the P-removal process were monitored. These measurements include dissolved acetate, phosphate, and ammonium; oxygen consumption; poly-β-hydroxybutyrate (PHB); glycogen; and active biomass. The model satisfactorily describes the dynamic behavior of all components during the anaerobicand aerobic phases.© 1995 John Wiley & Sons, Inc
    Zusätzliches Material: 12 Ill.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 10
    Digitale Medien
    Digitale Medien
    New York, NY [u.a.] : Wiley-Blackwell
    Biotechnology and Bioengineering 47 (1995), S. 585-595 
    ISSN: 0006-3592
    Schlagwort(e): biofilm ; wastewater treatment ; airlift reactor ; nitrification ; Chemistry ; Biochemistry and Biotechnology
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Biologie , Werkstoffwissenschaften, Fertigungsverfahren, Fertigung
    Notizen: For a stable and reliable operation of a BAS-reactor a high, active biomass concentration is required with mainly biofilm-covered carriers. The effect of reactor conditions on the formation of nitrifying biofilms in BAS-reactors was investigated in this article. A start-up strategy to obtain predominantly biofilm-covered carriers, based on the balancing of detachment and a biomass production per carrier surface area, proved tp be very successful. The amount of biomass and the fraction of covered carrier were high and development of nitrification activity was fast, leading to a volumetric conversion of 5 kgN · m-3 · d-1 at a hydraulic retention time of 1h. A 1-week, continuous inoculation with suspended purely nitrifying microorganisms resulted in a swift start-up compared with batch addition of a small number of biofilms with some nitrification activity. The development of nitrifying biofilms was very similar to the formation of heterotrophic biofilms. In contrast to heterotrophic bio-films, the diameter of nitrifying biofilms increased during start-up. The detachment rate from nitrifying biofilms decreased with lower concentrations of bare carrier, in a fashion comparable with heterotrophic biofilms, but the nitrifying biofilms were much more robust and resistant. Standard diffusion theory combined with reaction kinetics are capable of predicting the activity and conversion of biofilms on small suspended particles. © 1995 John Wiley & Sons Inc.
    Zusätzliches Material: 11 Ill.
    Materialart: Digitale Medien
    Bibliothek Standort Signatur Band/Heft/Jahr Verfügbarkeit
    BibTip Andere fanden auch interessant ...
Schließen ⊗
Diese Webseite nutzt Cookies und das Analyse-Tool Matomo. Weitere Informationen finden Sie hier...